07 TC Commando EZ2500 Remote Start Install

[macdiesel]

I am going to attempt to install a Commando EZ-2500 remote starter in my 2007 TC. Does anyone know where I could find a good wiring diagram of an 07 TC and/or a good install manual for this starter? The install manual that came with is very vague. Any help would be appreciated!

[navylife59]

Just tell me what are the input/ouputs needed for the unit and I will post up the schematics of what you need.

[macdiesel]

WHat exactly do you need to know about the input/outputs?

[navylife59]

PWR
GND
Door Lock/Unlock
Neutral Safety
IGN
Starter
Door Pin

et cetera

Basically everything that has to be wired to the car to make this function.

[NyTeRider]

You know...most install shops offer lifetime warranty on all services, and being an installer myself I am going to tell you that the majority of malfunctions that occur with security systems originate from the installation alone and the quality of work that was put forth. One single bad connection can leave you stranded in the middle of nowhere attempting to contact AAA to get your car towed to the nearest installation place because you forgot to connect the 2nd starter output to relay contact 87A instead of 87, and 86 was not connected properly to 30. But anyways...GOODLUCK!

12volts red (30A), white (25A) + ignition harness
Starter black + ignition harness
Second Starter green + ignition harness
Ignition blue + ignition harness
Second Ignition yellow + ignition harness
Third Ignition N/A
Accessory gray + ignition harness
Second Accessory N/A
Keysense black - ignition harness
Notes: Using the status output to trigger this wire during remote start will disarm the factory alarm without unlocking the doors.
Power Lock green to blue - driver kick, 20 pin plug, pin 15
Notes: Meter this wire while turning the key in the driver door key cylinder.
Power Unlock purple to pink (double pulse) - driver kick, 20 pin plug, pin 14
Notes: Meter this wire while turning the key in the driver door key cylinder.

Can also use the passenger door key cylinder wire for unlock, which only requires a single pulse. It is purple to lt. green (-) in the passenger kick, 10 pin plug, pin 7.
Lock Motor blue to brown 5wi driver kick, gray 7 pin plug, pin 6
Unlock Motor pink to blue 5wi driver kick, gray 7 pin plug, pin 5
Parking Lights+ brown + top of fuse box, 30 pin plug, pin 29
Parking Lights- brown - headlight switch
Hazards orange - hazard light switch
Turn Signal(L) yellow + top of fuse box, 30 pin plug, pin 27
Turn Signal(R) green + top of fuse box, 30 pin plug, pin 28
Reverse Light pink + top of fuse box, 14 pin plug, pin 2
Door Trigger orange (D), blue (P) - top of fuse box
Notes: The driver door is orange in a 30 pin plug, pin 21. The passenger door is blue in a 16 pin plug, pin 14. Use both wires and diode isolate each.
Dome Supervision blue - L side of fusebox, 6 pin plug, pin 2
Trunk/Hatch Pin purple - top of fuse box, 30 pin plug, pin 7
Hood Pin N/A
Trunk/Hatch Release orange - driver kick, gry 12 pin plug, pin 12
Notes: Meter this wire while using the back door opener switch on the hatch.

The hatch release motor wire is lt. green to white in the driver kick, gray 12 pin plug, pin 6.
Power Sliding Door N/A
Factory Alarm Arm arms with lock
Factory Alarm Disarm disarms with unlock
Disarm No Unlock use key sense wire
Tachometer black ac data link conn. under dash, pin 9
Notes: The tach wire is also found at the ECM behind the glove box, top plug, pin 5.
Wait to start N/A
Brake Wire blue + brake pedal switch
Parking Brake black - parking brake switch
Horn Trigger white - horn switch
Memory Seat 1 N/A
Memory Seat 2 N/A
Memory Seat 3 N/A
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Transponder
Part #: 556UW
Alternate Part1 #: 555U
Notes:

[macdiesel]

Thanks a lot for the help this far. We have almost got it installed with a few issues. Can anyone tell me exactly which relay (ignition or starter) is in the attached diagram? Also could you tell me what the diagram is trying to say? We have all of the other connectors installed and tested the voltages and we are stuck on the 5 pin connector. Thanks again.

Also does any one know how these toyota relays are numbered. I know relays from my old mustang were numbered on the relay itself, but these aren't.