Registration is FREE and takes seconds to complete!
Club-tC Members Receive:
» Advertisement Free Browsing
» Access to all tC Tech Articles
» Ability to post questions and comments
» Use of private message system
» Ability to share images
» Their own personal profile page
» More tC information then anywhere else
Sign Up Now!

Crank Pulley Install question

Discussion in 'Engine Performance' started by peruano85, Sep 17, 2007.

  1. Offline

    peruano85 New Member

    Member Since:
    Sep 8, 2005
    Location:
    2006 tC
    My Ride:
  2. 20 Scion tC
    does anyone know what the recommend torque is when replacing the crank pulley???
    peruano85, Sep 17, 2007
    #1
  3. Offline

    ForBiddeN New Member

    Member Since:
    Mar 10, 2007
    Location:
    2007 scion tc
    My Ride:
  4. 20 Scion tC
    its not rely torque u just pound it in there untill it fits in lol.
    ForBiddeN, Sep 17, 2007
    #2
  5. Offline
    • Staff / Moderator

    navylife59 Super Moderator

    Member Since:
    Mar 22, 2006
    Location:
    2005 Scion Tc
    My Ride:
  6. 20 Scion tC
    Correct Torque

    Crank Pulley Torque Setting.JPG

    N*m (kgf*cm, ft.*lbf) : Specified torque

    Instructions:

    INSTALL CRANKSHAFT PULLEY
    (a) Using SST, fix the pulley in place and tighten the
    bolt.
    SST 09213-54015 (91651-60855), 09330-00021
    Torque: 180 N*m (1,835 kgf*cm, 133 ft.*lbf)

    Note: No thread locker is required per the manual.
    navylife59, Sep 18, 2007
    #3
  7. Offline

    peruano85 New Member

    Member Since:
    Sep 8, 2005
    Location:
    2006 tC
    My Ride:
  8. 20 Scion tC
    so the torque is 180?
    peruano85, Sep 18, 2007
    #4
  9. Offline

    ForBiddeN New Member

    Member Since:
    Mar 10, 2007
    Location:
    2007 scion tc
    My Ride:
  10. 20 Scion tC
    hahaha holly **** my bad im use to outer cars on the 420a blocks it doesnt screw in u pound it in lol.
    ForBiddeN, Sep 18, 2007
    #5
  11. Offline

    peruano85 New Member

    Member Since:
    Sep 8, 2005
    Location:
    2006 tC
    My Ride:
  12. 20 Scion tC
    hahaha rubber mallet will come in handy i'm sure
    peruano85, Sep 18, 2007
    #6
  13. Offline

    ForBiddeN New Member

    Member Since:
    Mar 10, 2007
    Location:
    2007 scion tc
    My Ride:
  14. 20 Scion tC
    lol yeah on my frineds block we did a motor swap and we were takeing every thing off the old block and putting it on the new block it was a good 20min of pounding before we go it on.
    ForBiddeN, Sep 18, 2007
    #7
  15. Offline

    peruano85 New Member

    Member Since:
    Sep 8, 2005
    Location:
    2006 tC
    My Ride:
  16. 20 Scion tC
    damn it better not take that long lol or i'll be pissed at that thing
    peruano85, Sep 18, 2007
    #8
  17. Offline

    ForBiddeN New Member

    Member Since:
    Mar 10, 2007
    Location:
    2007 scion tc
    My Ride:
  18. 20 Scion tC
    well yours is just a bolt that goes in go get an inpact wrence and have some fun.
    ForBiddeN, Sep 18, 2007
    #9
  19. Offline
    • Staff / Moderator

    navylife59 Super Moderator

    Member Since:
    Mar 22, 2006
    Location:
    2005 Scion Tc
    My Ride:
  20. 20 Scion tC
    133 ft.*lbf
    navylife59, Sep 19, 2007
    #10

Share This Page

Users found this page by searching for:

  1. crankshaft pulley

    ,

  2. crank pulley